Q-SPRAY 150C - PU

Polyurethane Cartridge Sytem for easy coating of polystyrene.

Q-SPRAY 150C is a 2-component polyurethane hard coating, is solvent-free and particularly suitable for the coating of polystyrene and styrodur (EPS / XPS).

Q-SPRAY 150C hardens in about 10 seconds and can be applied to horizontal and vertical surfaces without without running off. Q-SPRAY 150C forms a hard, impact resistant surface. It can be sprayed into rubber molds to make fast, impact resistant castings.

To process Q-SPRAY 150C, our Cartridge Gun is required. Hardened Q-SPRAY 150C is highly shock-resistant and tough.

Q-SPRAY 150C

Q_SPRAY 150C Polyurethane <a title=paintingGOOD TO KNOW To paint symbols made from Styrofoam or Styrodur we highly recommend top quality acrylic paints without solvents. These paints are available ready to use in almost any color. An additional mixing bench will enable you to create any desired color yourself. The acrylic dispersions are suitable for the one-sided, visible or complete painting of letters and logos: • One-sided: Will only color the front or top. All other surfaces will be left untreated. • Visible side: The color application will cover all visible surfaces of the object. Therefore, only the front and the sides will be fully covered with paint. In the back, the letter or logo will receive either no or only a light protective layer. Coloring the visible sides is ideal for wall letterings. • Complete paint job: Ideal for letters and logos that you would like to hang up, put up or glue to transparent displays. For fast and inexpensive painting, it is recommended to use a paint spray gun. Such spray guns work with compressed air, which is why a compressor or a pump is required to operate the spray gun. We also highly recommend a painting wall to extract the spray mist. Further information about the safe handling of spray guns can be found on the American OSHA (Occupational Safety and Health Administration) website. ">Coating System" width="465" height="327" />


  • PRICE AT

    145,00 € + Tax

  • GET AN OFFER


Application

  • Protection, Reinforcing, Moulding
  • Props, Film & TV
  • Packing, special packing
  • Mold, formwork construction
  • Horizontal and vertical surfaces
  • In mould spraying with release agent
  • Hobby and Crafts

Specification

  • Reinforcing and protecting
  • Waterproofing and high impact resistant
  • No VOC’s and no odors
  • Direct application on polystyrene and Pur foam
  • Direct in mould application for reproduction of objects
  • Up to 5mm thickness
  • Hard, impact-resistant surface
  • Automatic mixing by double cartridge
  • Easy to use

Technical Data

Q-SPRAY Cartridge
Cartridge Capacity 2 x 750ml
Mix Ratio 1 : 1 ( 750ml x 750ml)
Covering 2 qm @ 0.7mm Dicke
  21 sq. ft. @ 30 mils
Shore D 70-75
Color off white
VOC free
Gel Time 10 sec
Tack free time 60 sec
Demoulding after 5-15 min
Paintable 5-15 min

Content of delivery

  • 3 filled Q-SPRAY 150C Cartridges
  • 3 Q-SPRAY Static Mixer, Atomizing Tip
  • Manual

To spray the Material our Q-SPRAY Cartridge Gun is needed and is not part of the delivery.

Delivery Q_SPRAY 150C Polyurethane <a title=paintingGOOD TO KNOW To paint symbols made from Styrofoam or Styrodur we highly recommend top quality acrylic paints without solvents. These paints are available ready to use in almost any color. An additional mixing bench will enable you to create any desired color yourself. The acrylic dispersions are suitable for the one-sided, visible or complete painting of letters and logos: • One-sided: Will only color the front or top. All other surfaces will be left untreated. • Visible side: The color application will cover all visible surfaces of the object. Therefore, only the front and the sides will be fully covered with paint. In the back, the letter or logo will receive either no or only a light protective layer. Coloring the visible sides is ideal for wall letterings. • Complete paint job: Ideal for letters and logos that you would like to hang up, put up or glue to transparent displays. For fast and inexpensive painting, it is recommended to use a paint spray gun. Such spray guns work with compressed air, which is why a compressor or a pump is required to operate the spray gun. We also highly recommend a painting wall to extract the spray mist. Further information about the safe handling of spray guns can be found on the American OSHA (Occupational Safety and Health Administration) website. ">Coating System" border="0" width="300" height="207"> Q-SPRAY

Optional Accessories

  • Q-SPRAY Cartridge Gun
  • Q-SPRAY Static Mixer
  • Q-SPRAY Primer

Delivery

  • About 1 weeks after receiving payment
  • Insured transportation via UPS or DHL
  • Pickup available